Mateksys R24-P6V ExpressLRS ELRS 2.4GHz 6CH PWM Vario Receiver Dual Antenna for RC Drone Airplane
Direct purchase from the factory 
Suroxit Rupantor
Moffat Dhod
Poth Prokria
Parthonn ProkriaMoffat Dhod
Roymall-ak Swagat, Tumche Dhod Store. Ami Tumche Avodd Pasun Moffat Dhod Ditat. Amche Dhod Sod ani Tumcho Dhod Ghe.Poth Prokria
Amchem Poth 2 Disam Bhitor.Normal Poth 5-7 Disam.Poth Kal Videshanchea Vellar Bodol Zait.1. Parthonn Prokria
Amkam roymall.com pasun Kinnnlelem Parthonn Ghetat. Moffat Dhod Parthonn Zainat. Dhod Upayog Zainaslem Parthonn Ghetat.Parthonn 3-5 Disam Bhitor Ghetat.Pasun Dhod Parthonn Zainat.Amkam Email: service@roymall.com va Whatsapp: +86193598494712.Rupantor
Parthonn Zalem Porthun Rupam Miletat. Poth Kharch Parthonn Zainat.Amkam Email: service@roymall.com va Whatsapp: +8619359849471Mateksys R24-P6V ExpressLRS ELRS 2.4GHz PWM Vario Receiver for FPV Racing Drone
Specifications:
ESP32-PICO-D4, SX1281, ExpressLRS Firmware
PA/LNA: SE2431L
RF Frequency: 2.4GHz ISM
Telemetry power: 22.5dbm (180mW)
Diversity: Antenna-switching, default ANT1
Barometer SPL06-001 (Vario)
Receiver output: 6x PWM CH
VBAT voltage sense: 0~25.5V
Antenna connector: IPEX MHF-1
Power supply: 4-13V DC @ u201cVu201d Pad
Power dissipation: 60mA~80mA@5V IN
PCB size: 30mm x 18mm
Weight: 4g w/ antenna
Firmwares
ExpressLRS
Receiver has ExpressLRS 3.3.2 preloaded with binding phrase u201c123456u201d, the Receiver will never enter binding mode if using the traditional binding procedure.
You need to reflash it with your binding phrase OR connect it to your PC/phone via WiFi and set your binding phrase in WebUI.
Tips
Full Resolution Switch Configuration Modes
Powering receiver with Reverse Voltage will damage the regulator chip. DOUBLE CHECK the power wires connected to the receiver.
Transmitter fw version should be EdgeTX 2.7.1/OpenTX 2.3.15 or newer
Flashing via Wifi
- Power on receiver. Receiveru2019s LED(Red) will blink slow at first, and after 30s, it should blink fast indicating itu2019s on Wifi Hotspot Mode.
-Wifi SSID u201cExpressLRS RXu201d, Password u201cexpresslrsu201d
Flashing via UART
1.Disconnect ESC and servos from receiver first.
2.Wire the receiver into the USB-TTL adapter, with TX(PWM 2 pin) on receiver connected to the Rx on the USB-TTL, and RX(PWM 3 pin) on receiver connected to the Tx of the USB-TTL. Wire 5V and GND of the USB-TTL to u201cVu201d and GND of the Receiver.
3.Press the boot button while powering on the receiver, then release u2013 the Red LED on receiver should now be solid on.
4.In configurator, Select the target Generic ESP32 PWM Vario 2.4Ghz RX, or RadioMaster ER6-GV and u201cUARTu201d for Flashing Method, set your bind phrase and Firmware Options , Check u201cerase before flashu201d and u201cForce FLash u201c.
Package Included:
1x ELRS-R24-P6V
2x IPEX MHF1 Antennas. 15cm
Dupont 2.54 pins (Board is shipped unsoldered)
